York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 75 / 160

JOHNSON CONTROLS

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

Pulldown Time Remaining

Displays the time remaining until the user programmed

Setpoint Oil Pressure is used. While this clock is dec-

rementing, the Target Oil Pressure Setpoint (fixed at

45.0 PSID) is in effect.

Oil Pump 2

Oil Pump Run Output (LED)

Illuminates when compressor #2 Variable Speed Oil

Pump is being commanded to run.

Pump Oil Pressure (HOP)

Displays the high side oil pressure measured at the

compressor #2 bearing input.

Oil Pressure

Displays the pressure differential between the Pump

oil pressure (HOP) transducer for compressor #2 and

the common Sump oil pressure (LOP) transducer. If

this compressor is the lead compressor, includes offset

pressure derived from auto-zeroing during compres-

sor #2 Pre-lube. However, if compressor #1 is the lead

compressor, this value includes offset pressure derived

from auto-zeroing during compressor #1 Pre-lube (re-

fer to auto-zeroing explanation under the Compressor

Screen). If either transducer used to calculate this dif-

ferential is out of range, the display field will show

XX.X.

Oil Pump Drive Command Frequency

Displays the speed command applied to compressor #2

Variable Speed Oil Pump.

Setpoint or Target Oil Pressure

Displays the oil pressure that compressor #2 Variable

Speed Oil Pump is controlling to. During the pre-lube

and for the first 15 seconds of System Run, this is the

Target Setpoint and is fixed at 45.0 PSID. For the re-

mainder of compressor #2 run, it is the programmed

Setpoint Oil Pressure.

Pulldown Time Remaining

Displays the time remaining until the user programmed

Setpoint Oil Pressure is used. While this clock is decre-

menting, the Target Oil Pressure Setpoint (fixed at 45.0

PSID) is in effect.

Oil Level (bar graph)

Displays the oil level in the oil sump as a vertical

graph. The range of the graph is 0% to 100%. Three

colors are used as follows: 0% to 35% - red; >35% to

80% - green; >80% to 100% - yellow. Only displayed

if enabled using the Oil Level Detection (Enable/Dis-

able) key.

PROGRAMMABLE
Oil Level Detection (Enable/Disable)

Access Level Required: SERVICE

Allows the user to enable or disable the Oil Level De-

tection feature. When enabled, displays the oil level in

the oil sump as a vertical graph.

NAVIGATION
Home

Access Level Required: VIEW

Causes an instant return to the Home Screen.

Oil Pump 1

Access Level Required: VIEW

Moves to a subscreen that allows manual control and

programming of the setpoints for compressor #1 Vari-

able Speed Oil Pump.

Oil Pump 2

Access Level Required: VIEW

Moves to a subscreen that allows manual control and

programming of the setpoints for compressor #2 Vari-

able Speed Oil Pump.

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды