York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 108 / 160

JOHNSON CONTROLS

108

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays the sales order parameters. The

Commissioning date is entered by the YORK Service

Technician at the time of chiller commissioning. The

remainder of the values are entered at the YORK Fac-

tory during the manufacturing of the chiller.

DISPLAY ONLY
Commissioning Date

Displays the date when the chiller was commissioned.

Job Name and Location

Displays the job name and location.

Model Number

Displays the chiller model number.

YORK Order Number

Displays the order number under which the chiller was

sold.

Panel Serial Number

Factory-defined serial number for the micropanel.

Chiller Serial Number

Factory-defined serial number for the chiller system.

Condenser and Evaporator Design Load

Information

Factory-defined description of the condenser and evap-

orator configuration at time of shipment.

Nameplate Information

Factory-defined information about the chiller motor

configuration. The Full Load and Inrush Amps is the

value for each motor.

System Information

Factory-defined conditions for which the chiller was

originally rated and sold. The Kilowatts Input is the

total for the chiller.

PROGRAMMABLE

None.

Print

Access Level Required: VIEW

This generates a listing of the Sales Order data.

SALES ORDER SCREEN

LD27879

FIGURE 40 -

SALES ORDER SCREEN

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды