York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 2 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

This equipment is a relatively complicated apparatus.

During rigging, installation, operation, maintenance,

or service, individuals may be exposed to certain com-

ponents or conditions including, but not limited to:

heavy objects, refrigerants, materials under pressure,

rotating components, and both high and low voltage.

Each of these items has the potential, if misused or

handled improperly, to cause bodily injury or death. It

is the obligation and responsibility of rigging, instal-

lation, and operating/service personnel to identify and

recognize these inherent hazards, protect themselves,

and proceed safely in completing their tasks. Failure

to comply with any of these requirements could result

in serious damage to the equipment and the property in

IMPORTANT!

READ BEFORE PROCEEDING!

GENERAL SAFETY GUIDELINES

which it is situated, as well as severe personal injury or

death to themselves and people at the site.
This document is intended for use by owner-authorized

rigging, installation, and operating/service personnel. It

is expected that these individuals possess independent

training that will enable them to perform their assigned

tasks properly and safely. It is essential that, prior to

performing any task on this equipment, this individual

shall have read and understood the on-product labels,

this document and any referenced materials. This in-

dividual shall also be familiar with and comply with

all applicable industry and governmental standards and

regulations pertaining to the task in question.

SAFETY SYMBOLS

The following symbols are used in this document to alert the reader to specific situations:

Indicates a possible hazardous situation

which will result in death or serious injury

if proper care is not taken.

Indicates a potentially hazardous situa-

tion which will result in possible injuries

or damage to equipment if proper care is

not taken.

Identifies a hazard which could lead to

damage to the machine, damage to other

equipment and/or environmental pollu-

tion if proper care is not taken or instruc-

tions and are not followed.

Highlights additional information useful

to the technician in completing the work

being performed properly.

External wiring, unless specified as an optional connection in the manufacturer’s product line, is not

to be connected inside the control cabinet. Devices such as relays, switches, transducers and controls

and any external wiring must not be installed inside the micro panel. All wiring must be in accor-

dance with Johnson Controls’ published specifications and must be performed only by a qualified

electrician. Johnson Controls will NOT be responsible for damage/problems resulting from improper

connections to the controls or application of improper control signals. Failure to follow this warn-

ing will void the manufacturer’s warranty and cause serious damage to property or personal injury.

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды