York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 82 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays information pertaining to the Me-

dium Voltage Variable Speed Drive (MVVSD), if in-

stalled. There are two similar screens available: one for

VSD 1 and another for VSD 2.

DISPLAY ONLY
PRV Position

Displays the Pre-rotation Vane position as a value be-

tween 0 and 100%.

Motor Run (LED)

Indicates whether the digital output from the controls is

commanding the motor to RUN.

Motor Heater (LED)

Indicates whether the digital output from the controls is

commanding the optional motor heater on. This LED is

not displayed if the option is not installed.

% Full Load Amps

Displays the motor current as a percentage of the Full

Load Amps (FLA) value.

Pulldown Demand Time Left

Displays the time remaining in the programmed pull-

down period if the value is nonzero.

Output Voltage

Displays the output voltage measured to the motor.

Output Frequency

Displays the present output frequency to the motor.

Input Power

Displays the total kilowatts measured by the VSD or

Harmonic Filter, if installed.

KW Hours

Displays the cumulative amount of kilowatts used over

time as the MVVSD motor controller operates.

Input Voltage

Displays the input voltage to the MVVSD as reported

by the MVVSD.

Output Current

Displays the average of the 3-phase output current to

the motor. Value is provided by the MV VSD.

DC Bus Voltage (Phase A, B, C)

Displays the three phases of DC bus voltage upper and

lower buses.

MEDIUM VOLTAGE VARIABLE SPEED DRIVE SCREEN

FIGURE 28 -

MEDIUM VOLTAGE VARIABLE SPEED DRIVE SCREEN

LD27867

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды