York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 74 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays a close-up of the chiller oil sump

with pertinent oil system status, pressures and tem-

peratures. This screen also serves as a gateway to sub-

screens that allow programming of setpoints for the

Variable Speed Oil Pumps for compressor #1 and #2.

DISPLAY ONLY
Oil Heater (LED)

Illuminates when the oil heater output is energized.

System Oil Return Solenoid (LED)

Illuminates when the oil solenoid output is energized.

Oil Sump Temperature

Displays the temperature of the oil in the sump.

Sump Oil Pressure (LOP)

Displays the low side oil pressure measured at the

sump.

Oil Pump 1

Oil Pump Run Output (LED)

Illuminates when compressor #1 Variable Speed Oil

Pump is being commanded to run.

Pump Oil Pressure (HOP)

Displays the high side oil pressure measured at the

compressor #1 bearing input.

Oil Pressure

Displays the pressure differential between the Pump

oil pressure (HOP) transducer for compressor #1 and

the common Sump oil pressure (LOP) transducer. If

this compressor is the lead compressor, includes offset

pressure derived from auto-zeroing during the com-

pressor #1 pre-lube. However, if compressor #2 is the

lead compressor, this value includes offset pressure

derived from auto-zeroing during compressor #2 Pre-

lube (refer to auto-zeroing explanation under the Com-

pressor Screen). If either transducer used to calculate

this differential is out of range, the display field will

show XX.X.

Oil Pump Drive Command Frequency

Displays the speed command applied to compressor #1

Variable Speed Oil Pump.

Setpoint or Target Oil Pressure

Displays the oil pressure setpoint that compressor #1

Variable Speed Oil Pump is controlling to. During the

pre-lube and for the first 15 seconds of System Run,

this is the target Setpoint, and is fixed at 45.0 PSID.

For the remainder of compressor #1 run, it is the pro-

grammed Setpoint Oil Pressure.

OIL SUMP SCREEN

FIGURE 24 -

OIL SUMP SCREEN

LD27863

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды