York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 96 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen provides a convenient location for pro-

gramming the most common setpoints involved in the

chiller control. This screen also serves as a gateway to

a subscreen for defining the setup of general system

parameters.

DISPLAY ONLY
Leaving Chilled Liquid Temperature

Setpoint

Displays the present setpoint to which the chiller is

operating whether controlled remotely or locally. This

value could come from a 0-20 mA, 4-20 mA, 0-10

VDC or 2-10 VDC input in Analog Remote mode,

PWM signal in Digital Remote mode, SC-EQ commu-

nications interface in ISN (BAS) mode, or a locally

programmed value.

Remote Range

Displays the Remote Range which is set by the Local

Leaving Chilled Liquid Temperature Range setpoint.

It is a value between 10ºF and 40ºF added to the Lo-

cal LCHLT Setpoint defining the maximum Remote

LCHLT setpoint.

Leaving Chilled Liquid Temperature Cycling

Shutdown

Displays the Leaving Chilled Liquid Temperature at

which the chiller will shut down to avoid over-cooling

the building. This value is calculated by subtracting the

Leaving Chilled Liquid Temperature Cycling Shut-

down Offset from the Leaving Chilled Liquid Tem-

perature Setpoint. If this value is below the absolute

minimum allowed shutdown temperature the mini-

mum value is displayed.

Restart

Displays the Leaving Chilled Liquid Temperature at

which the chiller will restart after it has shut down due

to cycling off on low water temperature. This value is

calculated by adding the Leaving Chilled Liquid Tem-

perature Cycling Restart Offset to the Leaving Chilled

Liquid Temperature Setpoint.

Chiller Current Limit Setpoint

Displays the current limit that is in effect during the

Chiller Steady State period (this period is in effect af-

ter the Chiller Pulldown Period is no longer in effect).

The Chiller Current Limit Setpoint could be from a

0-20 mA, 4-20 mA, 0-10 VDC or 2-10 VDC input in

Analog remote mode or PWM input in Digital remote

mode or SC-EQ communication interface in ISN (BAS)

remote mode or a Local Chiller Limit Setpoint entered

at the Keypad. The Chiller Pulldown Period is in effect

from the instant the chiller enters “System Run” until

the Leaving Chilled Liquid Temperature is within 2ºF

of the Leaving Chilled Liquid Temperature Setpoint.

During this period, the Chiller Pulldown Demand Limit

Setpoint is in effect. The Chiller Current Limit Setpoint

is in effect for the remainder of “System Run”.

SETPOINTS SCREEN

LD27873

FIGURE 34 -

SETPOINTS SCREEN

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды