York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 64 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

motor currents are balanced with 20%, whereupon it

automatically clears. If the Surge Window Count ex-

ceeds the Count Limit, the lag compressor is taken off

line and “Warning – Anti Surge –Surge Limit Exceed-

ed” is displayed. This is displayed until manually reset

with the Warning Reset Key.

Count Limit

Access Level Required: OPERATOR

Allows the user to define the maximum number of

surge events (2 to 8; default 3) that can occur within

the programmed Count Window period of time before

the lag compressor is taken off line. Each time a surge

occurs, the Surge Window Count is incremented. If the

Surge Window Count. If the number of surge events

within the Count window exceeds the Count Limit, the

lag compressor is taken off line and “Warning – Anti

Surge – Surge Limit Exceeded” is displayed. This will

be displayed until manually cleared with the Warning

Reset key.

Clear Surge Count

Access Level required: ADMIN

Allows user to reset dual compressor Total Surge

Count to zero.

High Head DP/P Limit

Access Level required: SERVICE

Specifies the Delta P/P head condition [(Condenser

pressure - Evaporator pressure) / Evaporator pressure],

above which the Lead compressor’s Pre-rotation Vanes

will be driven closed while the Lag compressor is start-

ing. This avoids surging during high head conditions.

NAVIGATION
Home

Access Level required: VIEW

Causes an instant return to the Home Screen.

Surge

Access Level Required: VIEW

Causes an instant return to the Main Surge Screen.

Lead Compressor

Identifies the compressor that has been assigned as the

lead compressor.

Lead % Full Load Amps

Displays the motor current of the lead compressor as

a percentage of the full load amps of that compressor

motor.

Lead PRV Position

Displays the position of the lead compressor pre-rota-

tion vanes position.

Lead VGD Position

Displays the position of the lead compressor Variable

Geometry Diffuser.

Lag %Full Load Amps

Displays the motor current of the lag compressor as

a percentage of the full load amps of that compressor

motor.

Lag PRV Position

Displays the position of the lag compressor pre-rota-

tion vanes position.

Lag VGD Position

Displays the position of the lag compressor Variable

Geometry Diffuser.

PROGRAMMABLE
Count Window

Access Level Required: OPERATOR

Allows the user to define the period of time (15 to

120 minutes; default 60) in which the number of surge

events are compared to the Count Limit threshold.

Each time a surge occurs, the Surge Window Count

increments. If the Surge Window count is less than or

equal to the Count Limit, a close signal is applied to

both compressor #1 and #2 Pre-Rotation Vanes until

compressor #1 motor current is within 20% of com-

pressor #2. While the vanes are closing, “Warning –

Anti Surge- Excess Surge Limit” is displayed until the

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды