YOKOGAWA 701210 Скачать руководство пользователя страница 34

Страница: 34 / 747

1-7

IM 701210-05E

Names and Functions of Parts

1.2

Panel Keys and Knobs

VERTICAL/HORIZONTAL Group Keys and Knobs

V/DIV

TIME/DIV

VERTICAL

HORIZONTAL

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

• CH1 to CH16 Keys (Chapter 5)

Displays a menu used to turn ON/OFF the display of each channel and set the

vertical position, coupling, probe type, offset voltage, bandwidth limit, expansion or

reduction of the vertical axis, linear scaling, and waveform labels. In addition, by

pressing this key before operating the V/DIV knob, the channel that is to be

controlled by the V/DIV knob can be selected. The indicator above each CH key

illuminates when the corresponding channel is ON.

In addition, pressing the SHIFT key followed by a CH key displays a menu

corresponding to the purple characters marked below and to the right of each key.

(CH1 to CH6: DSP1 to DPS6, CH9: LOGIC A, CH10: LOGIC B, CH11: EVENT)

Pressing the NUM KEY (see page 1-9) followed by a CH key causes the gray value

marked below and to the left of each key to be entered.

• V/DIV Knob (Section 5.3)

You can set the voltage sensitivity using this knob. Before turning this knob, you

press a key from CH1 to CH16 to select the target channel. If you change the

setting while the waveform acquisition is stopped, the setting takes effect when you

restart the waveform acquisition.

If you select a DSP channel (optional) by pressing the SHIFT key followed by one

of the CH1 to CH6 keys before turning this knob, you can change the Value/Div

setting of the DSP channel.

• TIME/DIV Knob (Section 5.2)

This knob is used to set the time axis scale. If you change the setting while the

waveform acquisition is stopped, the setting takes effect when you restart the

waveform acquisition.

TRIGGER Group Keys

MODE

POSITION

SIMPLE/ENHANCED

DELAY

ACTION

MANUAL TRIG

TRIGGER

TRIG D

TRIG’D indicator

Illuminates when a trigger
is activated.

• MANUAL TRIG Key (Section 6.19)

Press the key to forcibly activate a trigger.

• (SHIFT+) MODE Key (Sections 6.1 and 6.18)

Displays a menu used to select the trigger mode. Pressing the SHIFT key followed

by the MODE key displays a menu related to action-on-trigger or action-on-log-end.

• SIMPLE/ENHANCED Key (Sections 6.4 to 6.17)

Displays a trigger setup menu. If the indicator below and to the left of the key is

illuminated, simple trigger is enabled; if the indicator below and to the right of the

key is illuminated, enhanced trigger is enabled.

• (SHIFT+) POSITION Key (Sections 6.2 and 6.3)

Sets the trigger position. Pressing the SHIFT key followed by the POSITION key

allows you to set the trigger delay.

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 34 / 747

Результаты поиска

Содержание 701210

Отзывы: