YOKOGAWA 701210 Скачать руководство пользователя страница 329 | Manualshive

Страница: 329 / 747

YOKOGAWA 701210 Скачать руководство пользователя страница 329

9-10

IM 701210-05E

Extra Area

The extra area can be set only when the display (recording) format is set to Single, Dual,

Triad, or Quad.

When the Format Is Single

If extra area is turned ON, the top 16 cm of the recording area (20 cm) is used to
record waveforms, and the remaining 4 cm is used to record waveform information
(extra area). Annotations (see the next page) and logic waveforms are recorded in the
extra area. The default setting is OFF.

When the Format is Dual, Triad, or Quad

If extra area is turned ON, the area below each of the divided waveform recording
area is used to record the waveform information (extra area). If extra area is turned
OFF, the extra area between each waveform recording area disappears. The vertical
axis of each waveform recording area is adjusted automatically according to the paper
size and recorded. The default setting is ON.

Flexible Zone

The flexible zone can be set only when the display (recording) format is Single and the

extra area is OFF. The position in the recording area (20 cm) where each waveform is to

be recorded is set with Upper and Lower (%). The Upper value can be set in the range of

2% to 100%. The Lower value can be set in the range of 0% to 98%. Each value can be

set in 1% steps. The minimum width is 2%.
[Example] • When Flexible Zone on CH1 is set to Upper = 20% and Lower = 0%

The CH1 waveform is recorded in the area from the bottom to 4 cm of the
recording area.

• When Flexible Zone on CH2 is set to Upper = 80% and Lower = 20%

The CH2 waveform is recorded in the area from 4 cm to 16 cm from the

bottom of the recording area.

0 %

Upper: 20 %

Lower: 0 %

100 %

0 %

Upper: 80 %

Lower: 20 %

100 %

Recor

ding area

Recor

ding area

Paper feed direction

Paper feed direction

Graticule

Type

Select the graticule type from

, OFF, or

. The graticule setting is linked with the DISPLAY

menu > Graticule setting. However, if OFF is selected, the DISPLAY menu is set to

.

Dark/Light

Set the graticule Dark/Light setting to Light or Dark.

Width of the Vertical Scale: Width

Select how to set the vertical scale width.

1div:

Graticule obtained by dividing the recording area into 10 areas

10mm: mm graticule type

Graticule Type

Graticule Width

1 div

10 mm

1 div

10 mm

1 div

10 mm

No graticule lines

No graticule lines

Graticule lines that are printed

The format of the scale lines that are printed depending on the selected graticule
type and width is given in the table below.

OFF

9.4 Setting the Recording Format of T-Y Waveform Recording

«
...
327
328
329
330
331
...
»

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов