YOKOGAWA 701210 Скачать руководство пользователя страница 174

Страница: 174 / 747

5-14

IM 701210-05E

5.9

Zooming Vertically According to the Upper and
Lower Limits of the Display Range

<For a description of this function, refer to page 2-7.>

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press a key from

CH1

CH16

keys to select the desired channel.

To select a DSP channel (optional), press

SHIFT + CH1 (DSP1)

through

SHIFT

+ CH6 (DSP6)

Press the

Variable/Position

soft key. The Variable selection menu appears.

Press the

soft key.

Setting the Upper Limit

Press the

Upper/Lower

soft key to set the jog shuttle control to Upper.

Turn the

jog shuttle

to set the upper limit.

Setting the Lower Limit

Press the

Upper/Lower

soft key to set the jog shuttle control to Lower.

Turn the

jog shuttle

to set the lower limit.

Setting the Upper and Lower Limits Simultaneously

Press the

Upper/Lower

soft key to set the jog shuttle control to both Upper and

Lower.

Turn the

jog shuttle

to set the upper and lower limits without changing the

spacing between the two.

Note

Pressing RESET sets the maximum and minimum values of the measurement range to the
upper and lower limits.
•

When observing voltage

Upper: 10 times +V/div, Lower: 10 times –V/div

•

When observing strain

Upper: +FS, Lower: –FS

•

When measuring acceleration

Upper: 5000/(gain

sensitivity)

Lower: –5000/(gain

sensitivity)

•

When measuring frequency and other parameters on the frequency module

Upper: (Offset value) + (Value/div

30)

Lower: (Offset value) – (Value/div

30)

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 174 / 747

Результаты поиска

Содержание 701210

Отзывы: