YOKOGAWA 701210 Скачать руководство пользователя страница 265 | Manualshive

Страница: 265 / 747

YOKOGAWA 701210 Скачать руководство пользователя страница 265

6-47

IM 701210-05E

Triggering

6

Send Mail Operation

Sends e-mail messages to the address specified using Network > Mail Setup > Mail

Address in the MISC menu.

Note

•

If action-on-trigger is started, the data is acquired in single mode trigger regardless of the
trigger mode setting, and the specified action is carried out.

•

If action-on-stop is started, the data is acquired in Log mode regardless of the trigger
mode setting, and the specified action is carried out. The specified action is also carried
out when the measurement is stopped in the middle of the measurement.

Setting the Execution Mode of the Action-on Trigger/Action-on Stop at Power ON

You can select whether to enable the action-on-trigger or action-on-stop mode at power

ON. For example, turn this ON if you wish to continue the action-on-trigger or action-on-

stop operation after a power failure.

ON:

At power ON, the action-on-trigger/action-on-stop is set to the mode that was

used when the power was turned OFF.

OFF: Action Mode is turned OFF at power ON.

The initial setting is OFF.

Notes When Using the Action-on-Trigger/Action-on-Stop

• Action-on-trigger and action-on-stop cannot be used if the acquisition mode is

Average.

• You cannot change the settings while the action-on-trigger or action-on-stopis in

progress.

• The action-on-trigger or action-on-stop operation may slow down if there is access

from the network while the following action is in progress.

Printing/saving of the screen image data or saving of the waveform data

• Action-on-riggers other than mail transmission are not available when the Dual

Capture function is ON. Also, none of the action-on-triggers are available if the

firmware is of a version earlier than 4.01.

• You cannot use action-on-trigger or action-on-stop when the realtime recording to the

internal hard disk is ON.

Notes When Action Is Set to Save to File or Image Save

• Do not specify the root directory of the medium as the save destination directory.

(Only up to 512 files can be saved to the root directory of a medium that has been

formatted using the DL750/DL750P.)

• The maximum number of files that can be created in a single directory is 5000. Do

not place files in the save destination folder before starting the action-on-trigger or

action-on-stop operation.

• If you select Save to File and Image Save simultaneously, separate the folders

specified by the FILE menu and the IMAGE SAVE menu.

• If you selected Numbering for the file name assignment method (Auto Naming) in the

FILE menu and the IMAGE SAVE menu, the creation of files takes an extended

period when the number of saved files becomes large. When creating more than

2000 files, select Date for Auto Naming.

• When 5000 files are saved, the action-on-trigger or action-on-stop operation ends.

6.18 Setting the Action-on-Trigger

«
...
263
264
265
266
267
...
»

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов