YOKOGAWA 701210 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 747

YOKOGAWA 701210 Скачать руководство пользователя страница 111

3-8

IM 701210-05E

3.4

Connecting the Power Supply and Turning the
Power Switch ON/OFF

Before Connecting the Power

Make sure that you observe the following points before connecting the power. Failure to

do so may cause electric shock or damage to the instrument.

WARNING

• Before connecting the power cord, ensure that the source voltage matches the

rated supply voltage of the instrument and that it is within the maximum rated

voltage of the provided power cord.

• Connect the power cord after checking that the power switch of the instrument is

turned OFF.

• To prevent the possibility of electric shock or fire, be sure to use the power cord

for the instrument that was supplied by YOKOGAWA.

• Make sure to perform protective earth grounding to prevent the possibility of

electric shock. Connect the power cord to a three-pin power outlet with a

protective earth terminal.

• Do not use an extension cord without protective earth ground. Otherwise, the

protection function will be compromised.

• If an AC outlet that matches the power cord provided is unavailable and

protective grounding cannot be furnished, do not use the instrument.

Connecting the Power Cord

1.

Check that the power switch is turned OFF.

2.

Connect the power cord plug to the power connector on the left side panel.

3.

Connect the plug on the other end of the power cord to the outlet that meets the

conditions below. The AC outlet must be of a 3-prong type with a protective

earth ground terminal.

Item

Rated supply voltage

1

100 to 120 VAC/200 to 240 VAC

Permitted supply voltage range

90 to 132 VAC/180 to 264 VAC

Rated supply voltage frequency

50/60 Hz

Permitted supply voltage frequency range

48 to 63 Hz

Maximum power consumption

Approx. 200 VA (Reference value: 135 VA when
the built-in printer is not used and 16 channels are
running)

1. The DL750/DL750P can use a 100-V or a 200-V system for the power supply. The maximum

rated voltage of the power cord varies depending on its type. Check that the voltage supplied
to the DL750/DL750P is less than or equal to the maximum rated voltage of the provided
power cord (see page Part 1:iv) before using it.

3-prong AC
outlet

Power cord
(standard accessory)

«
...
109
110
111
112
113
...
»

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов