YOKOGAWA 701210 Скачать руководство пользователя страница 21

Страница: 21 / 747

Part 1:x

IM 701210-05E

Be sure to observe with the precautions below. Not complying might result in injury
or death.

WARNING

• Use the Correct Power Supply

Before connecting the power cord, ensure that the source voltage matches the

rated supply voltage of the instrument and that it is within the maximum rated

voltage of the provided power cord.

• Use the Correct Power Cord and Plug

To prevent the possibility of electric shock or fire, be sure to use the power cord

supplied by YOKOGAWA. The main power plug must be plugged into an outlet

with a protective earth terminal. Do not disable this protection by using an

extension cord without protective earth grounding.

• Connect the Protective Grounding Terminal

Make sure to connect the protective earth to prevent electric shock before

turning ON the power. The power cord that comes with the instrument is a

three-prong type power cord. Connect the power cord to a properly grounded

three-prong outlet.

• Do Not Impair the Protective Grounding

Never cut off the internal or external protective grounding wire or disconnect the

wiring of the protective grounding terminal. Doing so poses a potential shock

hazard.

• Do Not Operate with Defective Protective Grounding or Fuse

Do not operate the instrument if the protective grounding or fuse might be

defective. Also, make sure to check them before operation.

• Do Not Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of flammable liquids or vapors.

Operation in such an environment constitutes a safety hazard.

• Do Not Remove Covers

The cover should be removed by YOKOGAWA’s qualified personnel only.

Opening the cover is dangerous, because some areas inside the instrument

have high voltages.

• Ground the Instrument before Making External Connections

Securely connect the protective grounding before connecting to the item under

measurement or to an external control unit. If you are going to touch the circuit,

make sure to turn OFF the circuit and check that no voltage is present.

• Precautions to Be Taken When Using the DC Power Supply

• Make sure to perform protective earth grounding to prevent electric shock.

•

Connect the DC power cord after checking that the power switch of the

instrument is turned OFF. If you connect the power cord with the power switch

turned ON, sparks may be emitted and can lead to fire.

• Precautions to Be Taken When Using the Modules

• Do not apply input voltage exceeding the maximum input voltage, withstand

voltage, or allowable surge voltage.

•

To prevent the possibility of electric shock, be sure to furnish protective earth

grounding of the DL750/DL750P.

•

To prevent the possibility of electric shock, be sure to fasten the module screws.

Otherwise, the electrical protection function and the mechanical protection

function will not be activated.

•

Avoid continuous connection under an environment in which the allowable surge

voltage or greater voltage may occur.

Safety Precautions

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 21 / 747

Результаты поиска

Содержание 701210

Отзывы: