YOKOGAWA 701210 Скачать руководство пользователя страница 333

Страница: 333 / 747

9-14

IM 701210-05E

9.6

Recording Numeric Values

<For a description of this function, refer to page 2-43.>

Procedure

Before carrying out the procedure below, set the recorder mode and print style as follows

according to the procedures in section 9.2.

• Recorder mode: Chart Recorder

• Print style:

Numeric (numeric value recording)

Press the

Print Setup

soft key to display the print setup dialog box.

Setting the Output Destination

Use the

jog shuttle

and

SELECT

to set Output Device to Chart or File.

Setting the Output Interval

Use the

jog shuttle

and

SELECT

to set Interval to 1s or 60min.

If Chart is selected step 2, proceed to step 4.

If File is selected step 2, proceed to step 5.

Setting the Print Direction (If Chart Is Selected in Step 2)

Use the

jog shuttle

and

SELECT

to set Direction to Normal (the newest data is

at the top of the paper) or Rotation (the oldest data is at the top of the paper).

Proceed to step 8.

Setting the Output File (If File Is Selected in Step 2)

Setting Auto Naming

Use the

jog shuttle

and

SELECT

to select Auto Naming from OFF, Numbering,

and Date.

Setting the File Name

Use the

jog shuttle

and

SELECT

to select File Name. Then, enter the file

name using up to 16 characters according to the procedure in section 4.2.

Selecting the File Output Destination

Use the

jog shuttle

and

SELECT

to select File List. Then, select the file output

destination according to steps 14 to 17 in section 13.7. Proceed to step 8.

Displayed only when Output
Device is set to File

Note

Up to 10000 lines are output to the file. When 10000 lines are exceeded, writing stops.
However, the measurement continues.

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

RECORDER

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

DUAL

CAPTURE

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 333 / 747

Результаты поиска

Содержание 701210

Отзывы: