YOKOGAWA 701210 Скачать руководство пользователя страница 148

Страница: 148 / 747

4-10

IM 701210-05E

Operations Using a USB Mouse

You can use a USB mouse to operate the DL750/DL750P as you would using the front

panel keys. In addition, you can point to a desired item on a menu and click the item.

This is analogous to pressing a soft key corresponding to a menu and pressing the

SELECT key.

USB PERIPHERAL Connector

The USB mouse is connected to the USB PERIPHERAL connector on the left side panel

of the DL750/DL750P. For details on the USB PERIPHERAL connector, see page 4-7.

USB Mouse That Can Be Used

A USB mouse (with a wheel) conforming to USB HID Class Ver.1.1. can be used.

Note

•

For USB mouse devices that have been tested for compatibility, contact your nearest
YOKOGAWA dealer.

•

Some items cannot be specified when using a mouse without a wheel.

Connection Procedure

When connecting a USB mouse, directly connect the mouse to the USB PERIPHERIAL

connector using a USB cable as shown below. You can connect/disconnect the USB

mouse connector regardless of the power ON/OFF state of the DL750/DL750P (supports

hot-plug). When the power switch is ON, the mouse is detected and enabled

approximately 6 s after it is connected.

USB Mouse

DL750/

DL750P

FILE

SHIFT

HELP

MISC

NUM KEY

PROTECT

VOICE
MEMO

IMAGE
SAVE

PRINT

ESC

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

SNAPSHOT

CLEAR TRACE

MENU

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

Note

•

Do not connect USB devices other than USB keyboard, USB mouse, and USB printer to
the USB PERIPHERAL connector.

•

There are two USB PERIPHERAL connectors on the DL750/DL750P. However, do not
connect mouse devices to both connectors at the same time.

•

Do not connect and disconnect multiple USB devices repetitively. To do so, allow at least
10 s between connection and disconnection.

•

Do not connect or disconnect the USB cable after the power is turned ON until key
operation is ready (approximately 20 to 30 s).

Confirming the USB Mouse That Is Connected

The procedure for confirming the USB mouse that is connected to the DL750/DL750P is

the same as the procedure for confirming the USB keyboard. See page 4-8.

4.3 USB Keyboard/USB Mouse

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 148 / 747

Результаты поиска

Содержание 701210

Отзывы: