YOKOGAWA 701210 Скачать руководство пользователя страница 283 | Manualshive

Страница: 283 / 747

YOKOGAWA 701210 Скачать руководство пользователя страница 283

7-17

IM 701210-05E

Acquisition and Display

7

Explanation

The data can be recorded in realtime to the internal hard disk (optional).

The internal hard disk consists of the following drives.

Realtime:

For realtime recording. You can set the realtime recording area in the

range of 30% to 70% of the entire capacity of the internal hard disk when

you format the internal hard disk (see section 13.5).

HD-0, HD-1*: For saving various data.

*

HD-0 only if the internal hard disk is partitioned to 2; HD-0 and HD-1 if the internal hard disk is
partitioned to 3.

Waveforms That Are Realtime Recorded

All normal waveforms displayed on the screen are realtime recorded.

Possible Time Axis Range, Maximum Record Length, and Maximum Sample Rate

for Realtime Recording

Varies depending on the number of channels that are to be realtime recorded as follows:

Number or Channels

Time Axis Range

Maximum

Maximum

Record Length

Samlpe Rate

18 channels or more

20 s/div to 3 day/div

25 MW

5 kS/s

12 to 17 channels

20 s/div to 3 day/div

50 MW

5 kS/s

6 to 11 channels

6 s/div to 3 day/div

50 MW

10 kS/s

4 to 5 channels

3 s/div to 3 day/div

100 MW

20 kS/s

3 channels

2 s/div to 3 day/div

250 MW

50 kS/s

2 channels

1 s/div to 3 day/div

500 MW

100 kS/s

1 channel

1 s/div to 3 day/div

1 GW

100 kS/s

Realtime recording is possible within the maximum record length and maxim sample rate
ranges of the number of channels to be realtime recorded.
The setting shown above is common to all models (memory options standard, M1, M2,
and M3).

Realtime Recording Mode

If you select Single, the following two trigger modes are available. If you select

Continue, only Log is valid.
Auto: Acquisition is started by pressing START. If the specified record length is

exceeded, old data is overwritten. Acquisition continues until you press STOP.

Log:

Acquisition is started by pressing START. When the specified record length is
reached, acquisition stops.

Sequence/Count

Single:

Acquisition is started by pressing START. When the specified record length is

reached, acquisition stops.

Continue: Acquisition is started by pressing START. When the specified record length is

reached, acquisition stops. This sequence is repeated the specified number

of times (count).

Auto Naming

File names are automatically created during realtime recording. You can also enter
comments. The following three auto naming types are available.

• OFF

File name specified by File Name (up to 16 characters).

• Numbering

Automatically creates files by attaching a four-digit number, 0000 to 4999, to the file

name. You can assign a common name before the number (Specified with File
Name. Up to 4 characters).

7.7 Realtime Recording to the Internal Hard Disk (Optional)

«
...
281
282
283
284
285
...
»

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов