Wazer WAZER Main Unit Скачать руководство пользователя

Страница: 53 / 69

Output

LP Pump:

This function engages the Low Pressure Pump for a short time. You may hear a light

humming noise as well as see water being circulated in your tank.

Dump Valve:

This function engages the Dump valve for a short time. You may hear a clicking

sound being emitted from the Right Side Cavity area, once to open the valve and once to close it.

Vibration Motors:

This function engages vibration motors for a short time. You can discern a

constant buzzing sound from the Abrasive Hopper.

Abrasive Valve:

This function engages the Abrasive Valve for a short time. You may hear a clicking

sound being emitted from the Right Side Cavity area, once to open the valve and once to close it

HP Valve:

This function engages the High Pressure Valve for a short time. You may hear a soft click

sound from the Right side cavity. If High pressure plumbing retains water pressure at this moment,

this function will clear the residual pressure from High pressure lines.

HP Pump:

This function engages the pump box for a short time. You may hear AC motor running

in the Pump Box.

Jog:

This feature enables you to move the nozzle to any point on the Cut Bed by manually

controlling the buttons on control pad.

Cut Rate Testing

The WAZER will cut a series of arcs at increasing speeds to help you determine the cutting
parameters for a new material.

General Cut:

Run this cut when you have no idea how fast the WAZER should cut you material.

This test will use the most material and have the least fine resolution.

Fast Cut:

Run this when you know that you material should cut on the faster side.

Medium Cut:

Run this when you know that you material should cut in the middle of our range.

Slow Cut:

Run this when you know that you material is going to be slow, typical for materials on

the thicker or harder side.

Firmware version

This feature display the current firmware version installed in WAZER control unit.

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды