Wazer WAZER Main Unit Скачать руководство пользователя страница 5

Страница: 5 / 69

Important Safety Information

Read and Understand User Manual Before Use

WARNING: Read all safety warnings, instructions, illustrations and specifications

provided with this power tool. Failure to follow all instructions listed below may

result in electric shock, fire, serious injury, property damage, serious injuries, or

death. Always read this entire manual before operating WAZER.

The employer or owner is responsible for compliance with all applicable federal, state and local

regulations/codes.

Always keep this manual in a safe, accessible location near WAZER during

operation and maintenance. Save all warnings and instructions for future

reference.

Signal Words

Throughout this document, the product labels, and in other collateral materials, you will come

across various signal words. Some of these signal words alert you to safety hazards. These

are important to the safety of WAZER users. Others are there to make sure your machine or

environment does not suffer any damage. Be sure to familiarize yourself and all other users of the

machine with these signal words. Make sure to refer back to this section as needed.

SAFETY ALERT SYMBOL

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible serious injury or death. This safety

alert symbol precedes any safety message about risk of personal injury.

It may also have one of the following signal words:

DANGER

Indicates a hazardous situation that, if not

avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation that, if not

avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation that, if not

avoided, could result in minor or moderate injury.

NOTICE

Indicates a hazardous situation that, if not

avoided, could result in property damage.

SECTION

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды