Wazer WAZER Main Unit Скачать руководство пользователя страница 25

Страница: 25 / 69

Hose 2: Install the Water Drain Hose

WAZER outputs a significant amount of water during cutting. For this reason, the Water Drain Hose

must be connected to your drain before operation.

Make sure you are draining waste water appropriately. The water drained from WAZER is partially

filtered. There will likely be some Used Abrasive and Material in the drained water.

Connect the Water Drain Hose to WAZER

Main Unit

In your Accessory Kit, you will find a Water

Drain Hose (1/2” diameter White Hose).

Connect this hose to the Water Drain

Hose Connection located in the back-right

corner of WAZER. Note that the Water

Drain Hose Connection swivels for more

direct routing.

You may choose to untwist the twist

tie holding the Signal Cable and Power

Transformer wire to the back of WAZER

for better access to the Water Drain Hose

Connection and to the High-Pressure Hose

Connection.

Route the Water Drain Hose

This will likely be similar to your Water Inlet

Hose routing. Zip tie the hose to other

plumbing or use the provided wall anchors;

avoid rough or sharp contact points.

Secure this to the drain

It is OK for the Water Drain Hose to empty into

a basin, as long as the hose is well-secured.

Make sure the drain is no more than 4 feet

above WAZER. Note that WAZER outputs a

significant amount of water while cutting.

An unsecured hose can quickly spill large

amounts of water.

Set

tin

g Up W

AZER |

TION 4

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды