Wazer WAZER Main Unit страница 56 Скачать руководство пользователя

Страница: 56 / 69

Checking the Abrasive Flow Rate

WAZER does not actively monitor and measure its Abrasive Flow Rate. However, the Abrasive

Flow Rate is a critical parameter, so you should check and monitor this regularly. It is also one of

the first things to check if your cut performance has seemed to change This rate will need to be

updated from time to time simply because of normal wear or from an unexpected event such as a

backflow.

Required Tools

•

Scale w/ accuracy of +/- 0.5g (+/-0.02oz) and

capacity of at least 200g ( 7 oz)

•

Cup with a volume of 250ml (8oz)

1. Start out with 3kg +/-0.25kg (6.6lbs +/-0.6) of

Abrasive in the hopper.

2. Open Abrasive drawer.

3. Remove Abrasive Valve Plug.

4. Select Setup and Maintenance.

5. Select Abr. Flow Rate.

6. Place (or hold) a cup or container below the

Abrasive Valve.

7. Now hit okay to begin the flow of abrasive.

•

If the valve simply doesn’t open consistently

see Machine Procedures > Pinch Valve

Teardown.

•

The timer will count while the abrasive is

flowing.

8. After the 1 min Abrasive Flow test weigh the

container with the Abrasive, then subtract

the weight of the container. This is the

abrasive rate per minute. The goal abrasive

rate is between 140 g/min - 162 g/min (4.94

oz/min - 5.71 oz/min). If the rate is lower than

that you should investigate your Dry Abrasive

system for the problem. If it is higher then

that your Abrasive Orifice is worn out, contact

Support for a replacement.

Maint

enan

ce |

TION 7

104

105

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды