Wazer WAZER Main Unit Скачать руководство пользователя

Страница: 6 / 69

Safety Symbols

In addition to the signal words listed above, WAZER has various product safety signs and safety

labels placed in visible locations. These labels are critical to your safety. You must familiarize

yourself and other users with their meaning. Ignoring these labels may result in equipment or

property damage as well as physical injury or death.

These product safety signs and labels should be periodically inspected and cleaned as necessary

to maintain good legibility. If they are no longer legible, the product safety Labels should be

replaced. For product safety labels that are lost or damaged, contact WAZER customer support for

replacement labels and recommended installation procedure.

The following symbols may be included on the on-product labels or in this User Manual:

TEAM LIFT

Always use two people to lift heavy components.

HOT SURFACE HAZARD

Avoid contact with hot surfaces during operation.

CUT/SEVER HAZARD

Avoid contact with the Jet or High-Pressure components during

operation.

ENTANGLEMENT HAZARD

Avoid contact with components in motion during operation.

ELECTRICAL SHOCK HAZARD

Avoid contact with all exposed electronics during operation.

EYE PROTECTION

Always wear appropriate eye protection to avoid potential

injuries to your eyes.

Read & Understand User Manual

Read and understand operator’s manual before using this

machine. Failure to follow operating instructions could result in

death or serious injury.

Product Safety Label Locations

Upon unboxing, you will be greeted with WAZER Main Unit in a state like this. Keep in mind all the warning label locations,

as they will convey important safety-related message for anyone operating, maintaining and repairing this machine.

This label warns you of the operation, maintenance,

and repair hazards of the WAZER Main Unit.

This label warns you of the heavy weight of the

WAZER Main Unit and instructs you to use the

proper lifting technique when moving it.

Upon unboxing, you will be greeted with WAZER Pump Box in a state like this. Keep in mind all the warning label locations,

as they will convey important safety-related message for anyone operating, maintaining and repairing this machine.

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды