Wazer WAZER Main Unit Скачать руководство пользователя

Страница: 29 / 69

VIDEO

Anchor WAZER to the Wall

Now that you have completed all the necessary connections, position WAZER and Pump Box into

their final locations.

The Pump Box can be slid further under the bench or WAZER so that it is out of the way. Make

sure to allow for plenty of air circulation around the Pump Box and do not stress the water or

Power Cables on the back of the unit.

The Wall Anchor helps to ensure the accuracy of the Cut by dampening any vibration you may

cause by accidentally bumping into WAZER while it is cutting.

When WAZER is filled with water it will weigh approximately 400 lbs (180kg). To

ensure the safety of the WAZER and its users it is required that you anchor the

machine to a wall or solid structure with the provided bracket and hardware.

To anchor WAZER:

1. Install the Wall Mount Bracket using the provided hardware. The bracket is installed on the

back-right side of WAZER (when viewed from behind) with a 4 mm Allen key.

2. Move WAZER into position and mark the wall where you intend to drill holes for the

appropriate Wall Mount Bracket.

3. Move WAZER away from the wall to drill holes or install wall anchors. Then, move it back and

install the appropriate screws through the bracket.

Note that wall anchors for both drywall and concrete are provided. Please install the

appropriate hardware.

Set

tin

g Up W

AZER |

TION 4

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды