Wazer WAZER Main Unit Скачать руководство пользователя страница 7

Страница: 7 / 69

This label warns you of the residual

hazards inside the WAZER Pump Box

Electrical Enclosure and instructs for

it to not be opened up.

This label warns you of the heavy

weight of the WAZER packages and

instructs you to use the proper lifting

technique when moving them.

This label instructs you to the

correct orientation that the WAZER

packages need to be maintained in

at all times.

This label warns you that the

WAZER contents inside may contain

carcinogenic materials according

to the state of California. For more

information, visit the listed website.

This label warns you of the electric

shock hazard associated with an

improper hose disconnect procedure.

It also serves to instruct you of the

proper disconnect procedure.

This label warns you of the existence

of the high temperature hazard near

its proximity.

This label warns you of the suffocation

danger when dealing with plastic bags.

Keep this bag away from children.

This label warns you of the operation, maintenance,

and repair hazards of the WAZER Pump Box.

This label warns you of the heavy weight of the

WAZER Pump box and instructs you to use the

proper lifting technique when moving it.

This label warns you of the electric shock hazard

associated with an improper hose disconnect

procedure. It also serves to instruct you of the

proper disconnect procedure.

This label warns you of the hazards associated

with an improper opening of the WAZER Pump

Unit. It also serves to instruct you of the proper

opening procedure.

This label warns you of the existence

of the high temperature hazard near

its proximity. Caution is advised to

avoid injury.

This label warns you of the suffocation

danger when dealing with plastic bags.

Keep this bag away from children.

This label warns you not to operate

the high-pressure hose line under

pressure exceeding the maximum

working pressure

Saf

y |

TION 2

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды