Wazer WAZER Main Unit страница 63 Скачать руководство пользователя

Страница: 63 / 69

Cleaning the Water Inlet Filter

All the water going into the system is filtered at the water inlet of the pump. Over time, this can

accumulate debris and sediment commonly found in most water mains. If you have particularly

old plumbing, you may need to clean your filter more often. Additionally if there was a broken

pipe in you neighborhood you can have ,more debris in the water for a time, this is more

common in the winter as pipes freeze. There are two in-line water filters on your WAZER to

cleanout. One is a canister style that you installed during the setup of your WAZER and another

is built in to the Pump Box.

Water Filter 1 - Canister Style:

1. Remove the Water filter from the bracket. DO NOT attempt to do this step while

mounted to the wall.

2. Place the drain hose into a sink or bucket

3. Turn the valve until water starts coming out of the drain hose. You will notice that

wipers will start to remove the debris caught on the filter

4. After a few turns the valve at the bottom of the Water Filter will open and this debris

will be removed from the water filter.

5. Turn the valve to close it

6. Replace the water filter onto its bracket.

Inlet Water Filter 2 - Pump Box Filter

Look into the back of your Pump Box where the hoses enter. At the bottom you will see the

Water Inlet and just past it a clear viewing area for filter. If it is anything but clean you need to

Tools needed

•

29 mm or 1 1/8” Socket

•

or a 1/2” hex wrench

Maint

enan

ce |

TION 7

118

119

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды