Wazer WAZER Main Unit страница 8 Скачать руководство пользователя

Страница: 8 / 69

General Power Tool Safety Warning

Read all safety warnings, instructions, illustrations and specifications provided

with this water jet cutter. Failure to follow all instructions listed below may result in electric shock,

fire and/or serious injury.
Save all warnings and instructions for future reference.

Work area safety

•

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

•

Set up and operate the water jet cutter where the floor surface and surrounding area are

water resistant and slip resistant. Water is likely to spill during routine use, set up and

maintenance of water jet cutters. Wet floor surfaces may increase the risk of slip and fall

which can result in serious personal injury.

•

Water jet cutters must be operated only by persons familiar with their operation and

manufacturer’s instructions. Operation of water jet cutters by persons unfamiliar with their

operation and manufacturer’s instructions can result in electric shock, fire and/or serious

injury.

•

Keep children and bystanders away from the water jet cutter while it is operating, and do

not allow unsupervised children and bystanders to interact with the water jet cutter at any

time. Other people in the work area may cause distractions, and persons unfamiliar with the

operation of the water jet cutter may change its setup, which may increase the risk of electric

shock, fire and/or serious injury.

Electrical safety

•

Before using the water jet cutter, test all Ground Fault Circuit Interrupter (GFCI) or Portable

Residual Current Device (PRCD) provided to ensure they are operating correctly. A properly

operating GFCI/PRCD reduces the risk of electrical shock.

•

Do not use the water jet cutter with extension cords. The GFCI/PRCD on the machine power

cord will not prevent electrical shock from the extension cords.

•

Water jet cutter plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) water jet cutters. Unmodified plugs and matching

outlets will reduce risk of electric shock.

•

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the water jet

cutter. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

•

While operating the water jet cutter, avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

•

Before every operation of a water jet cutter, make sure that the water connections and water

piping and joints are leak-free. Water leaks may increase the risk of electric shock.

•

Because the electronics will be operating around water, both power cables have integrated

GFCI/PRCD protection. Do not attempt to use any cables that are not GFCI/PRCD protected.

•

DO NOT attempt to use any other Power Supply other than the one included by WAZER

•

The replacement of the Power Cables and Power Supply shall only be carried out by the

manufacturer or approved service organization.

Personal safety

•

Stay alert, watch what you are doing and use common sense when operating a water jet

cutter. Do not use water jet cutter while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while operating Water jet may result in

serious personal injury.

•

Use personal protective equipment. Always wear eye protection. Protective equipment

such as safety glasses, non-skid safety shoes, waterproof gloves and hearing protection will

reduce personal injuries.

This label warns you of the heavy weight

of the WAZER Main Unit and instructs

you to use the proper lifting technique

when moving it. You may peel it off after

installation.

This label instructs you to not plug

in the power to the machine prior to

being sure that all previous steps were

completed successfully. You may peel

it off after acknowledging our terms of

service and installation.

This label instructs you to lift from

the correct location when installing or

moving the WAZER Main unit to not

cause damage to the machine. You

may peel it off after installation.

This label instructs you to be sure to

fill the WAZER Main Unit to the correct

level before expecting it to turn on. You

may peel it off after installation.

This Label instructs you to replace the

Pump Vent Cap before any connections

are made in order to not harm your

WAZER Pump Box. You may peel it off

after installation.

This label instructs you to the proper

lifting technique and locations when

installing or moving the WAZER Pump

Unit in an effort to not damage the

machine. You may peel it off after

installation.

Peel-able Labels

You may peel them off after the installation process of your WAZER is completed.

Saf

y |

TION 2

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды