Wazer WAZER Main Unit Скачать руководство пользователя

Страница: 20 / 69

Unboxing the Pump Box

Please follow these instructions to properly unbox the Pump Box:

1. Cut the straps that wrap the box and cut the tape on the top of the box to unfold its flaps.

DO NOT make a deep cut into the box as you will scratch the Pump Box.

2. Remove the surrounding packaging.

(Two-person lift)

With one person on each side, grab the bottom of the two aluminum side

plates, lift the Pump Box and place it near its final location. Be careful not to allow your fingers

to be pinched as you set the it down.

4. Carefully open and remove the unit from the bag that it is wrapped in. There may be some

residual water from the testing process.

5. Leave access to the Pump Box’s rear connections.

We strongly recommend placing the unit

on the ground directly underneath or near WAZER.

Make sure it is easy to see the Pump Box

so that you can easily detect leaks.

6. Inspect the unit exterior for any damage. This includes scratches, dents or cracks to the

exterior of the WAZER pump box.

ONLY lift the Pump Box using the bottom of the silver plates on the left and

right sides. We recommend you to retain the packaging for return and decommissioning, if

required.

Verify Your Shipment’s Contents

In an effort to improve your WAZER experience, there may be additional items that we include with

your shipment. It is likely they are included to aid in the setup, maintenance, or operation of your

WAZER.

•

1x – User Manual

•

1x - WAZER Main Unit

•

1x - Pump Box

•

1x - WAZER Power Cable (GFCI/PRCD)

•

1x - Water Filter Kit

Setup Kit

•

1x - SD Card

•

1x - Pump Vent Cap

•

1x - 17mm Wrench

•

2x - Water Sensor

•

1x - Wall Anchor Kit

1x - Wall Mount Bracket

3x - Sheet Rock Anchor

3x - Sheet Rock Fastener

3x - Concrete Wall Anchor

2x - M5x10 Hex Screws

1x - 4 mm Allen Key

Plumbing Kit

•

1x - Garden Hose Adapter

•

1x - Sink Adapter

•

1x - Sink Drain Adapter Kit

•

1x - On/Off Valve

•

8x - #3 Hose Routing Anchors

•

8x - #4 Hose Routing Anchors

•

10x - 6" Zip-Ties

Spare Parts and Toolkit

•

2x - Fuse

•

1x - Nozzle Height Tool

•

1x - Nozzle Cover

•

1x - Abrasive Hose

•

2x - Abrasive Hose End

•

1x - Orifice

•

2x - Abrasive O-ring

•

12x - 25 mm Fastening Screws

•

12x - 40 mm Fastening Screws

•

1x - Cut Bed Installation Tool

•

2x - Abrasive Plug

•

4x - High-Pressure O-Ring

•

1x - Phillips #2 Driver

•

1x - Needle Nose Pliers

•

1x - Deburring Tool

•

1x - File

Hose Kit

•

1x - High-Pressure Hose (sturdy black hose

with metal connectors)

•

1x - Water Inlet Hose (3/8” diameter white

hose)

•

1x - Water Drain Hose (1/2” diameter white

hose)

Oil Kit

•

-1x - Oil

•

1x - Oil Funnel

Set

tin

g Up W

AZER |

TION 4

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды