Wazer WAZER Main Unit Скачать руководство пользователя

Страница: 23 / 69

Hose 1: Install the Water Inlet Hose

The Water Inlet Hose needs to be connected to your water source at one end and to the Pump Box at

the other end.

Make sure the Pump Box is placed near its final location

Lave access to the rear of the unit.

Connect Water Inlet Hose to Pump Box:

In your Accessory Kit, you will find a Water Inlet

Hose (3/8” diameter White Hose.) Connect this hose to the Water Inlet Connection on the rear

of the Pump Box. Leave enough slack in the hose to be able to pull the Pump Box out, remove

the cover, and access the rear if needed in the future.

Route Water Inlet Hose:

Route the rest of the hose to your water source. We recommend

routing along piping or at the base of a wall. Do not place the hose near items that could

cause abrasion (i.e. bolts, sharp metal plates, etc.).

Every installation will be different, but we recommend using zip ties and the provided hose

routing anchors to help with tidy routing. Do not cut the hose yet.

Here are some routing examples that may be helpful:

Connect Water Inlet Hose to water supply:

Now we will make the connection to your plumbing. We have provided hardware for two types

of connections.

You will either use:

- the Garden Hose Water Inlet Adapter, or

- the Sink Adapter.

NOTE: Pick whichever one is most appropriate for your current setup. If both options are available,

we recommend the Sink Adapter because you can leave the hose installed permanently, whereas

this may not be the case for the Garden Hose Adapter.

DO NOT cover the Pump Box.

DO NOT place the Pump Box in a confined area.

The Pump Box generates significant heat that needs to be expelled and should be visible at all

times to inspect for leaks.

GARDEN HOSE ADAPTER

SINK ADAPTER

Set

tin

g Up W

AZER |

TION 4

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды