Wazer WAZER Main Unit Скачать руководство пользователя страница 64

Страница: 64 / 69

3. Loosen the Thumb Screw securing the

pump cover. Remove the cover.

4. With one hand secure the Brass Nut

then remove the plastic water inlet hose

connector. This should only be hand tight

5. Use the wrench to loosen the retaining

nut.

6. Pull off the plastic filter cover and the

screen.

1. Follow the proper procedure for High

Pressure Hose disconnection displayed

on the warning label. Then remove the

High Pressure Hose from the Pump

Box. Let the water drip dry.

2. Remove the Inlet Water Line. Press

in on the grey collar before pulling the

hose out. Let the water drip dry.

Procedure

9. Place the plastic cover over with

the metal end nut. Re-secure with the

wrench you have. Sealing here is all

achieved by o-rings, so be careful and

do not over-tighten.

10. Use one hand to hold the brass nut

and screw on the inlet hose connector.

11. Replace the Pump Box Cover,

tighten the Thumb Screws, reattach all

plumbing and electrical connections

and you are ready to resume cutting.

7. Clean off any debris off all surfaces. First

rinse off what you can then scrub off the

stubborn bits. The risk here is that a small

particle can be sucked through and get

stuck in the pump seals.

8. To re-assemble first place the screen

back on .

Maint

enan

ce |

TION 7

120

121

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды