Wazer WAZER Main Unit Скачать руководство пользователя страница 41

Страница: 41 / 69

Shutdown WAZER

Once you have completed your Cut, perform the following Shutdown procedure:

Close the On/Off Valve

Turn the On/Off Valve to the “off” position.

Turn WAZER Off

WAZER has a single Power Switch located in the bottom-right corner. Flip this switch to turn

WAZER off. Do not use the Emergency stop switch at the top of your machine as your main

power switch.

Empty the Used Abrasive

We recommend that you remove the Used Abrasive Buckets from their retainers and place

them up on the Cut Bed after every Cut. This allows them to fully drain their water into the

Tank, which means you won’t have to deal with water in your Used Abrasive disposal area.

However, you may empty the Used Abrasive at any time, so this step isn’t critical to perform

during shutdown if you regularly do it upon startup.

Bacteria can build up in the standing water of the Tank. Any injuries or cuts,

even minor ones, should be treated with caution. If you have open wounds avoid contact with the

water or wear gloves that do not expose you to the Tank water

Leave the Door Open

After a Cut, everything inside WAZER is wet. We suggest leaving the Door open so the internal

surfaces can dry. This prevents tight areas from growing mold and allows you to brush away the

Used Abrasive once it is dry. It is much more difficult to clean the Used Abrasive when it is wet.

Perform a General Inspection

It is always a good idea to inspect WAZER for leaks and abnormal wear:

•

Is there water around WAZER or Pump Box?

•

Are there any pieces of the Cut Bed that stick out, or are there pieces of cut Material lodged

in it?

•

Are the Bellows sealed against the aluminum Gantry Blocks?

Are the rubber gaskets around the inside of the machine correctly seated around the

machine (ie. back of the tank, edges of the door, back of the block that has the Cutting

Head mounted to it).

•

Do any hose lines leading up to the cutting head have too much tension?

The sooner you notice and fix a problem the better. Most importantly, you MUST

remember you are dealing with water, which can result in things such as electrical shorts and

water damage. Prevent a serious problem from occurring by paying attention to your WAZER.

tin

g W

ith W

AZER |

TION 5

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды