Wazer WAZER Main Unit страница 68 Скачать руководство пользователя

Страница: 68 / 69

Warranty

Overview

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT

VARY FROM STATE TO STATE. TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY AND THE

REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES

AND CONDITIONS, WHETHER ORAL, WRITTEN, STATUTORY, EXPRESS OR IMPLIED. WAZER

DISCLAIMS ALL STATUTORY AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND WARRANTIES

AGAINST HIDDEN OR LATENT DEFECTS, TO THE EXTENT PERMITTED BY LAW. INSOFAR AS SUCH

WARRANTIES CANNOT BE DISCLAIMED, WAZER LIMITS THE DURATION AND REMEDIES OF SUCH

WARRANTIES TO THE DURATION OF THIS WARRANTY AND, AT WAZER’S OPTION, THE REPAIR OR

REPLACEMENT SERVICES DESCRIBED BELOW. SOME STATES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY MAY LAST, SO THE LIMITATION DESCRIBED ABOVE MAY NOT

APPLY TO YOU.

SECTION

What is Covered by this

Warranty?

WAZER grants an Exclusive Limited Warranty

(the “Warranty”) for the WAZER Desktop or

WAZER Standup (the “Product”), and warrants

against defects in materials and workmanship

when used normally in accordance with

WAZER’s instructions for a period of six (6)

months from the original date of receipt by the

purchaser (the “Warranty Period”).

What is Not Covered by

this Warranty?

This Warranty does not apply:

•

To consumable parts, unless failure has

occurred due to a defect in materials or

workmanship;

•

To cosmetic damage, including, but not

limited to, scratches, dents, and broken

plastic unless failure has occurred due to a

defect in materials or workmanship;

•

To damage caused by use with a third party

component or product that does not meet

WAZER’s specifications;

•

To damage caused by accident, abuse,

misuse, fire, liquid contact to electronic

components, earthquake or other external

causes;

•

To damage caused by operating the Product

outside WAZER’s instructions or improper

cleaning of the Product;

•

To damage caused by service (including

upgrades and expansions) performed by

anyone who is not a representative of WAZER

(except for damage that results from do-it-

yourself warranty repairs, discussed below,

if the repair was conducted according to

WAZER instructions);

•

To a Product that has been modified to alter

functionality or capability without the written

permission of WAZER;

•

To defects caused by normal wear and tear

or otherwise due to the normal aging of the

Product;

•

If any serial number has been removed or

defaced from the Product;

•

If WAZER receives information from relevant

public authorities that the product has been

stolen, and you cannot prove in any way that

you are the authorized user of the Product

(e.g., by presenting proof of purchase);

•

To items consumed or expended by their

normal use, such as the Nozzle, Orifice

and Cut Bed (if you do cause damage from

incorrect use, WAZER may be able to send

you replacement parts and you may have to

pay for them);

•

To damage or defect caused by: etching,

including any non-through-cutting; cutting

or attempting to cut material greater than

the maximum thickness specified for that

material in the User Manual or on the

website; servicing the Product with the Water

Inlet Valve opened or with the Power Cables

plugged in; accident, flood, fire, or other

external causes outside of WAZER’s control;

modification of the Product;

•

The Product’s software or firmware

•

To damage occurring during transportation

of the Product (such claims are the sole

responsibility of the shipper).

Use of third-party abrasive does not in and

of itself void this warranty. However, damage

caused by use of third-party abrasive is

excluded from this warranty.

Conditions

The Warranty is granted under the following

conditions:

•

The Product was assembled, sold and

delivered by WAZER.

•

The Product was purchased new from WAZER

or authorized reseller by the claimant, or by a

member of the same household, or member

of the same institution/organization of the

original purchaser.

•

The then-latest firmware was installed and

used in the Product.

•

The install and maintenance instructions in

the User Manual were followed.

•

In the event that a warranty has expired, or is

void, basic email support is offered to allow

for the purchase of replacement parts of

components. Troubleshooting services are

not offered for machines out of warranty.

Providing evidence of the satisfaction of these

conditions is a prerequisite for any remedy

under the Warranty.

Transfer of Warranty

The transfer of an existing warranty is granted

if the following conditions are met:

•

The transfer is from one member of the

household to another or from one member

of the institution/organization to another.

•

WAZER is notified within ten (10) business

days of this transfer and can be validated

through address verification and/or domain

of the new “owner”. Providing evidence

of the satisfaction of these conditions is

a prerequisite for any remedy under the

Warranty.

Procedure

If you encounter an issue with the Product, here

is the procedure to follow:

1. Consult your User Manual for help.

2. Submit a claim by emailing WAZER at

[email protected] within the Warranty

Period.

3. Provide proof of purchase, including the

original purchaser’s invoice.

4. Help diagnose any issues related to your

claim. This may involve corresponding

with WAZER’s support team by email or

phone and by sending images, videos or

files related to your claim. Any warranty

claim must first be accepted by WAZER as

justified.

5. If your claim is accepted, WAZER, at its sole

discretion will either:

a. Send new or refurbished parts for you to

install, along with detailed instructions

for do-it-yourself (“DIY”) parts service.

You may be required to send the original

parts to WAZER before or after your

replacement parts are sent. WAZER is

not responsible for any labor costs you

incur relating to DIY parts service. A

replacement part assumes the remaining

term of the Warranty or ninety (90) days

from the date of replacement or repair,

whichever provides longer coverage for

you; or

b. Send you a replacement new or

refurbished Product that’s substantially

equivalent in function, formed from

new and/or previously used parts that

are equivalent to new in performance

and reliability. The replacement Product

assumes the remaining term of the

Warranty or ninety (90) days from the

date of replacement, whichever provides

longer coverage for you; or

c. Refund you the purchase amount. If

so, you may be required to return the

original Product prior to or after receiving

the refund.

6. The shipping cost (including any duties

and taxes) for any new or refurbished

parts or Product sent to you in fulfillment

of your warranty claim shall be covered by

WAZER. WAZER will ship via non-expedited

fulfillment by default. Expedited shipping

may be available at an added cost to the

128

129

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Похожие инструкции для WAZER Main Unit

Бренды по названию

Популярные бренды