Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 142

background image

Creating a Configuration

|

3-37

Pilot Plus

XX200-00

Alarm Action

The Alarm Action screen is used to select the priority level and video
switching actions to take place when alarms are activated. This screen
applies to all alarms, regardless of type (RS-232, receiver or X-IA input
alarms). Up to 128 alarm inputs are available.

The alarm inputs are listed by number in the Alarm Input # column in the 2-
column table on the left. Selecting an alarm input number in that column will
cause the alarm input number to be displayed in the 5-column table Alarm
Input #. You can then set the parameters for alarm input by selecting the field
columns, which are described in the following table. A description of each
field parameter is displayed on the screen when the field is selected.

Field Description

Priority

Used to assign a priority level to an alarm input. Up to
129 priority levels are available (0 to 128) with the
lower numbers having a higher priority. #### indicates
the alarm is being used as a trigger input. Refer to the

Admin

section for more information on trigger inputs.

«
...
76
77
78
79
80
...
»

Содержание PILOT PLUS V1544















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PILOT PLUS V1544

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 5

Бренд: ICP DAS USA Страницы: 64

Бренд: ICP DAS USA Страницы: 7

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: RAKwireless Страницы: 6

Бренд: Frico Страницы: 12

Бренд: Linak Страницы: 2

Бренд: Beckhoff Страницы: 30

Бренд: Festo Страницы: 109

Бренд: Topworx Страницы: 8

Бренд: DAYLIFF Страницы: 40

Бренд: Velux Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды