Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 57

Страница: 57 / 142

3-16

Chapter 3 Configuration

XX200-00

Pilot Plus

2. Upon selection, the title below Available Field will change to the

parameter selected and the appropriate values will display in the
selection box.

3. Select All for all keypads, Selected Only for a keypad that is

highlighted in the list or From to specify a range of keypads.

4. Click Update to implement the changes.

Note:

The Settings box contains two buttons: Apply and Restore. Clicking

Apply will make the changes permanent. Clicking Restore will cancel the
changes that you have made and revert back to the original values. Once
you click Apply, you cannot restore the original values.

Keypad Groups

Refer to the

Timed Events

section in this chapter for a description of Keypad

Groups.

Keypad/Monitor Partitions

Refer to the

Partitioning

section for a description of how monitors are

partitioned to keypads.

Содержание PILOT PLUS V1544















































































































































Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды

Vicon PILOT PLUS V1544, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды