Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 142

background image

3-22

|

Chapter 3 Configuration

XX200-00

Pilot Plus

Field Description

Ack Action

The acknowledge action specifies the action to take
place after all alarms in the monitor stack are
acknowledged. The Store setting restores pre-alarm
video. The Blank setting displays a blank monitor (no
video signal) and the No Action setting leaves the
video from the alarm site on the monitor. #####
indicates option is unavailable for monitors that are not
Alarm Monitors.

First Avail Priority

Sets Alarm Monitor priority, which defines the alarm
monitor that will be used when alarms are activated.
Priority levels are from 1 – 32.

All selections are made using the Options Wizard. To change a field’s value,
proceed as follows:

1. Select the field that you wish to modify using the Available Field

selection box. You can scroll through all available options.

2. Upon selection, the title below Available Field will change to the

parameter selected and the appropriate values will display in the
selection box.

3. Select All for all monitors, Selected Only for a monitor that is

highlighted in the list or From to specify a range of monitors.

4. Click Update to implement the changes.

Note:

The Settings box contains two buttons: Apply and Restore. Clicking

Apply will make the changes permanent. Clicking Restore will cancel the
changes that you have made and revert back to the original values. Once
you click Apply, you cannot restore the original values.

«
...
61
62
63
64
65
...
»

Содержание PILOT PLUS V1544















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PILOT PLUS V1544

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: JBM Страницы: 35

Бренд: IAI Страницы: 5

Бренд: Oceanic Systems Страницы: 8

Бренд: Samson Страницы: 8

Бренд: Samson Страницы: 60

Бренд: Samson Страницы: 40

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: Blucave Страницы: 2

Бренд: Conel Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды