Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 142

background image

3-14

|

Chapter 3 Configuration

XX200-00

Pilot Plus

Keypads

You can define up to 8 keypads in the system. To begin, access the Control
Keypads screen by selecting it from the menu bar or by double-clicking it in
the system summary. The Keypads Groups and Keypad/Monitors Partitions
menus are also referenced in this section.

The keypads are listed by number in the Keypad # column. The parameters
that can be set for each keypad are contained in the field columns, which are
described in the following table. A description of each field parameter is
displayed on the screen when the field is selected.

Field Description

Alarm Ack

Selecting Enabled or Disabled will enable or disable
the keypad’s ability to acknowledge an alarm.

Default Monitor

This setting defines the monitor that will automatically
be selected at the specified keypad when the system
is initially powered or rebooted. The default monitor
must be a monitor partitioned to the keypad currently
selected. See the Keypad/Monitor Partitions screen
description for more information.

«
...
53
54
55
56
57
...
»

Содержание PILOT PLUS V1544















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PILOT PLUS V1544

Бренд: Radio Shack Страницы: 52

Бренд: IBM Страницы: 105

Бренд: Campbell Страницы: 8

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: Lamtec Страницы: 136

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Paradox Страницы: 2

Бренд: LLURIA Страницы: 2

phyCORE-MCF548x

Бренд: Phytec Страницы: 104

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Бренд: Simplex Страницы: 40

Бренд: Sartorius Страницы: 165

Бренд: Adaptec Страницы: 2

Бренд: Webasto Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды