Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 142

background image

2-16

|

Chapter 2 Installation and Operation

XX-200-00

Pilot Plus

Function Keys

Key Description

TOUR

To start a tour, enter a tour number on the numeric
keypad and press TOUR to initiate the respective tour.
For example, pressing 1 and then TOUR will start Tour
1.

You can also use the TOUR key to advance to the next
step of the tour, bypassing the dwell time. During an
alarm, you can switch to the next alarm in the stack,
without acknowledging an alarm by pressing TOUR.

Note:

The tour has to have been defined previously using

the Configurator.

To reset all Crosspoints, enter 999 or 990 on the keypad
and press TOUR. This will clear all video Crosspoints
momentarily.

PRESET

The PRESET key can be used to store or recall PTZ
presets.

To store a Preset: Press PRESET followed by a number
on the numeric keypad and then ENTER. For example, to
set up Preset 23, press PRESET > 23 > ENTER.

To recall a Preset: Press PRESET followed by the preset
number on the numeric keypad and then PRESET again.
For example, to recall Preset 23, press PRESET > 23 >
PRESET.

Note:

The Preset Store function can be disabled using

the General System Settings screen in the Configurator.
Preset Recall is always active. Refer to the

Configurator

chapter,

Tools

section for more information.

MENU

Press MENU to adjust the LCD display brightness,
adjust the joystick speed, enable or disable audible
alarm indication and enable or disable audible clicks
when the touch-sensitive front panel is touched.

To scroll through the menu, use the joystick up and
down keys. To select a particular menu, press ENTER.
To save an option, press ENTER. To back out of a
menu, press BACK.

«
...
31
32
33
34
35
...
»

Содержание PILOT PLUS V1544















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PILOT PLUS V1544

Бренд: ABB Страницы: 2

Бренд: Radarcan Страницы: 40

Бренд: National Instruments Страницы: 2

Бренд: RAKwireless Страницы: 6

Бренд: Vega Страницы: 20

Бренд: WAGO Страницы: 56

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Yamaha Страницы: 2

Бренд: ZKTeco Страницы: 13

Бренд: UniPi Technology Страницы: 4

Бренд: POLA Страницы: 2

Бренд: Watlow Страницы: 20

Synergy SGY-101

Бренд: Fairford Страницы: 20

Бренд: Varian Страницы: 37

Бренд: UUGear Страницы: 38

Бренд: Simplex Страницы: 78

Бренд: Lumel Страницы: 32

Бренд: D-M-E Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды