Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 103

Страница: 103 / 142

3-62

Chapter 3 Configuration

XX200-00

Pilot Plus

Alarm Enable Event

Field Description

Event #

This column will display the selected event number.

Alarm Pattern

Alarm pattern selected for the event. Alarm Patterns
are defined using the Alarm Input Controls screen.
Refer to the Alarms section.

Schedule Date

The date the event will take place or begin if event
will occur more than once. Date format is:
MM/DD/YYYY.

Schedule Hour

The hour of the day the event will take place. Hour
format is: 24-hour mode (0 – 23).

Schedule Minute

The minute the event will take place. Minute format
is: 0 – 59.

Frequency

The amount of times the event will occur. Values
are: Not Set, Once, Weekly, Daily, Monthly.

Day of Week

This field will automatically be populated
automatically based on the date, time and
frequency settings.

All selections are made using the Options Wizard. To change a field’s value,
proceed as follows:

Содержание PILOT PLUS V1544















































































































































Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды

Vicon PILOT PLUS V1544, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды