Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 49

Страница: 49 / 142

3-8

Chapter 3 Configuration

XX200-00

Pilot Plus

Monitors

Monitors Submenu

Description

Monitor Displays

Accesses the Monitor Displays
screen, which enables you to define
settings for the monitors.

TDT Position

Accesses the OSD screen, which
allows you to set display
parameters for the monitors.

Alarms

Alarms Submenu

Description

Alarm Stack Mode

Accesses the Alarm Stack Mode
screen that allows you to select
Common Stack, Independent Stack
or First Available alarm activity.

Alarm Action

Accesses the Alarm Action screen,
which enables you to define settings
for the alarms.

Receiver Action

Accesses the Receiver Action
screen, which allows you to define
settings for the PTZ cameras upon
alarm.

Input Controls

Accesses the Alarm Input Controls
screen, which enables you to define
settings for X-IA and RS-232
devices.

Содержание PILOT PLUS V1544















































































































































Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды

Vicon PILOT PLUS V1544, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды