Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 30

Страница: 30 / 142

Installation

2-13

Pilot Plus

XX200-00

6. Connect the terminal block plug into the respective alarm terminal block.

Alarm Relay Output

Note:

Refer to the

Cable Recommendations

section in the

Maintenance

chapter for information on the type of cables to be used for twisted-pair
connection.

The Alarm Relay output provides a control output to an external device,
which may be wired normally open or normally closed. Connect the external
device as follows:

1. Select the 3-Position Terminal Block Plug, part number F004802505 from

the Accessory Kit.

2. Route the appropriate wires from the external device to the unit.

3. Using wire strippers, remove approximately 0.25 in. (0.64 cm) from the

two wires.

4. Note the position of pin 1 on the terminal block.

5. Connect the wires from the external device in accordance with the pinout

data that follows.

Pin #

Name

Normally Closed

2 Common

3 Normally

Open

6. Connect the terminal block plug into the ALARM RELAY terminal block.

Содержание PILOT PLUS V1544















































































































































Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды

Vicon PILOT PLUS V1544, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды