Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 142

background image

Creating a Configuration

|

3-47

Pilot Plus

XX200-00

Salvo Tour

Field Description

Tour #

Use this field to select the tour number from 1 – 32.
The tour selected will display in the Tour # field in
the 5-column table.

Tour Type

Use this field to select a Monitor or Salvo tour.

Last Step Action

Use this field to select the action that will take place
as the final step in a tour. Three last step actions
are possible: another tour may be activated (Chain),
all touring may cease (Halt), or the tour may repeat
(Repeat). The Chain command gives you the option
to select any of the tour numbers, for example,
Chain # 23 to select tour number 22.

Note:

When chaining tours, add 1 to the tour

number that you want to chain. Therefore if you
want to chain to tour 1, you would Chain # 2. If you
enter 0, the tour will repeat. Entering 1 halts the
tour.

Step #

This field lists the steps available in a tour from 1 –
32. Each step is performed in sequence and can
have a different set of actions. The actions are set
using the other fields in the table.

«
...
86
87
88
89
90
...
»

Содержание PILOT PLUS V1544















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PILOT PLUS V1544

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Waterway Страницы: 16

Бренд: Aaeon Страницы: 76

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: V2 ELETTRONICA Страницы: 6

Бренд: Hach Страницы: 210

Бренд: Harpo Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды