Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 142

background image

3-20

|

Chapter 3 Configuration

XX200-00

Pilot Plus

Note:

The Settings box contains two buttons: Apply and Restore. Clicking

Apply will make the changes permanent. Clicking Restore will cancel the
changes that you have made and revert back to the original values. Once
you click Apply, you cannot restore the original values.

Camera Partitions

Refer to the

Partitioning

section for a description of how cameras are

partitioned.

Monitors

You can set various parameters for all or select monitors in the system up to
the system maximum of 8. To begin, access the Monitor Displays screen by
selecting it from the menu bar or by double-clicking it in the system summary.
The TDT Position menu is also described in this section.

The monitors are listed by number in the Monitor # column. The parameters
that can be set for each monitor are contained in the field columns, which are
described in the following table. A description of each field parameter is
displayed on the screen when the field is selected.

Note:

This screen may also be accessed from the Video Switch Setup menu

by selecting the Default CallUp Values submenu.

«
...
59
60
61
62
63
...
»

Содержание PILOT PLUS V1544















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PILOT PLUS V1544

Бренд: Waters Страницы: 55

Бренд: Paradox Страницы: 2

Бренд: GANTERUD Страницы: 24

Бренд: Barco Страницы: 2

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: HandyTrac Страницы: 14

Бренд: TA Страницы: 6

Бренд: Samson Страницы: 48

Бренд: ZIGBEE Страницы: 5

Бренд: Oceanic Страницы: 11

Бренд: RADVision Страницы: 3

Бренд: RADEMACHER Страницы: 48

Бренд: R&M Страницы: 53

Бренд: ZKTeco Страницы: 6

Бренд: Balboa Water Group Страницы: 88

Бренд: ABB Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды