Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 28

Страница: 28 / 142

Installation

2-11

Pilot Plus

XX200-00

Alarm Inputs

Note:

Refer to the

Cable Recommendations

section in the

Maintenance

chapter for information on the type of cables to be used for twisted-pair
connection.

Alarm Inputs are wired directly into the Pilot Plus. There are two 16-position
terminal blocks labeled ALARM 1-16 and ALARM 17-32 on the rear panel.
Connect the alarms as follows:

1. Select the 16-Pin Terminal Block Plug, part number S56G0000004 from

the Accessory Kit.

Note:

There are four terminal block plugs. One for each 16-pin upper and

lower bank on the terminal blocks.

2. Route the appropriate wires from the alarms to the unit.

3. Using wire strippers, remove approximately 0.25 in. (0.64 cm) from the

two wires.

4. Note the position of pins 1, 9, 17 and 25 on the respective terminal blocks.

5. Connect the wires from the alarms to the plugs in accordance with the

pinout data that follows.

ALARM 1-16 Terminal Block Plug

Pin #

Name

Pin #

Name

ALARM 1

ALARM 9

2 GND 2 GND

ALARM 2

ALARM 10

4 GND 4 GND

ALARM 3

ALARM 11

Содержание PILOT PLUS V1544















































































































































Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды

Vicon PILOT PLUS V1544, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды