Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 142

background image

2-14

|

Chapter 2 Installation and Operation

XX-200-00

Pilot Plus

Relay/Audio Switcher (AUDIOSWITCH)

The Pilot Plus may be connected to Vicon’s Relay/Audio-Follow-Video
Switchers. Use of a relay/audio switcher allows audio and video signals to be
switched simultaneously, via the Pilot Plus's internal video switching system.
For example, the audio signal from an intercom microphone associated with
a camera can be switched to a speaker at the guard station at the same time
the video is switched to the guard’s monitor.

One ribbon cable is required to connect the Pilot Plus to a relay/audio
switcher. This cable is included with the Relay/Audio-Follow-Video Switcher.
It is connected to the AUDIOSWITCH port on the rear panel of the unit.

Note:

In the Configurator, ensure that Tools/Global Settings/VSYNC is set to

Enabled.

«
...
29
30
31
32
33
...
»

Содержание PILOT PLUS V1544















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PILOT PLUS V1544

Бренд: ABB Страницы: 52

Бренд: MADRIX Страницы: 36

Бренд: Ebyte Страницы: 35

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: Federal Signal Corporation Страницы: 34

Бренд: ICP DAS USA Страницы: 6

Бренд: Jabra Страницы: 18

Бренд: Lattice Semiconductor Страницы: 2

Бренд: Lathem Страницы: 4

Бренд: tams elektronik Страницы: 36

Бренд: Xylem Страницы: 48

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

Бренд: YASKAWA Страницы: 30

Бренд: Tylo Страницы: 51

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды