Vicon PILOT PLUS V1544 Скачать руководство пользователя страница 121

Страница: 121 / 142

3-80

Chapter 3 Configuration

XX200-00

Pilot Plus

Field Description

LCD Brightness

Use this control to set the brightness of the front
panel LCD display. Settings from 0 – 255 are
provided. Default is 91.

NTSC or PAL

Set this control to the type of system you are using.
Default is NTSC.

VSYNC

Set to Enabled to provide vertical synchronization.
Default is Disabled.

Note:

For VSYNC to work, a reference camera

must be connected to input 128 of the camera
inputs. The other cameras in the system must have
their V-Syncs aligned to the reference camera.

Click Update to save your changes.

Note:

The Settings box contains Apply and Restore buttons. Clicking Apply

will make the changes permanent. Clicking Restore will cancel the changes
that you have made and revert back to the original values. Once you click
Apply, you cannot restore the original values.

Содержание PILOT PLUS V1544















































































































































Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды

Vicon PILOT PLUS V1544, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PILOT PLUS V1544

Отзывы:

Похожие инструкции для PILOT PLUS V1544

Бренды по названию

Популярные бренды