Vacon 50X Скачать руководство пользователя | Manualshive

Страница: 34 / 132

background image

33

vacon

connections

Tel. +358 (0)201 2121 • Fax +358 (0)201 212205

4

4.5 Terminals Found on the Vacon 50X Control Board

4.5.1 Description of the Control Terminals

Figure 12 shows the control terminals found on the I/O board of the Vacon 50X AC drive. See page 9 for
specifications. Table 10 on page 33 describes the control terminals.

The drive’s control terminals are referenced to earth ground through a resistor / capacitor network. Use
caution when connecting analog signals not referenced to earth ground, especially if the communications
port (J3) is being used. The J3 port includes a common reference that can be connected to earth ground
through the host PLC or computer.

Figure 12: Vacon 50X Control Terminals

Terminal

Description

Vmet

Analog output 1, which is a dedicated voltage output.
The default signal range is from 0 to 10 Vdc (5 mA maximum). It is proportional to the variable
configured by parameter 700 (Vmet Config) (see page 79). It may be calibrated while the drive
is running via parameter 701 (Vmet Span) (see page 79).

Imet

Analog output 2, which is a dedicated current output.
The default signal ranges from 0 to 20 mAdc (50 to 500

Ω

). It is proportional to the variable

configured by parameter 702 (Imet Config) (see page 80). It may be calibrated while the drive is
running via parameters 704 (Imet Offset) and 703 (Imet Span) (see page 80).

Vin1

Analog Input 1, which is used to provide speed references.
The default input signal is 0 to 10 Vdc (the type of input signal is selected with parameter 205
(Vin1 Config); see page 64). Parameters 206 (Vin1 Offset) and 207 (Vin1 Span) may be used to
offset the starting value of the range and the size of the range, respectively; see page 64 for
more information.

If a 0 to 20 mAdc input signal is configured, the burden is 250 ohm. If a 0 to 10 Vdc input
signal is configured, the input impedance is 475 kohm.

A potentiometer with a range of 1 to 2 kohm is suggested for this input.

+10

This terminal is a +10 Vdc source for customer-supplied potentiometers. The maximum load on
this supply cannot exceed 10 mAdc.

Table 10:Description of Vacon 50X Control Terminals

«
...
32
33
34
35
36
...
»

Содержание 50X





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 50X

Бренд: Walimex Pro Страницы: 68

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: Mamas & Papas Страницы: 44

Бренд: Mamas & Papas Страницы: 8

Бренд: Omegalink Страницы: 2

Бренд: MamaLove Страницы: 9

Бренд: Rain Bird Страницы: 138

Бренд: Rane Страницы: 2

Бренд: Jäger Страницы: 18

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: YASKAWA Страницы: 340

Бренд: TUYA Страницы: 28

MultiLoad II EXL

Бренд: Toptech Страницы: 83

Бренд: Winbond Страницы: 85

Бренд: Brooks Страницы: 66

Бренд: ccei Страницы: 16

XBee DigiMesh 2.4

Бренд: Digi Страницы: 157

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды