Vacon 50X Скачать руководство пользователя | Manualshive

Страница: 63 / 132

background image

vacon 50x parameters

vacon

62

24-hour s358 (0)40 837 1150 • Email: [email protected]

7

Parameter 109, Power On Hours, displays how long the drive has been powered up.

Parameter 110, Stator Frequency, displays the frequency the drive is applying to the mo-
tor stator.

Parameter 111, DC Bus Voltage, displays the voltage on the DC bus.

This parameter displays the power being output by the drive in terms of drive rating. The
measurement is calculated by scaling the Load Torque value by the ratio of Volt-Amps to
Rated Volt-Amps, and adjusted by Output Frequency.

Parameter 201, the Input Mode parameter, configures local and remote control of the
Start/Stop source and the reference source.
The following data values may be assigned to this parameter:

Parameter Value

Run/Stop Control

Local only

Local keypad operation only

Remote only

Terminal strip operation only

L/R Rem Ref

LOCal Keypad Start/Stop and Speed

REMote Keypad Start/Stop, Terminal Strip Speed Reference

L/R Rem Ctl

LOCal Keypad Start/Stop and Speed

REMote Keypad Speed Reference, Terminal Strip Start/Stop

L/R Rem Bth

LOCal Keypad Start/Stop and Speed

REMote Terminal Strip Start/Stop and Speed Reference

EMOP

{1} {2} {4}

Terminal strip operation using Increase/Decrease buttons

EMOP2

{1} {3} {4}

Terminal strip operation using Increase/Decrease buttons

LOC/EMOP

{1} {2} {4}

LOCal Keypad Start/Stop and Speed

REMote Terminal strip operation using Increase/Decrease

LOC/EMOP2

{1} {3} {4}

LOCal Keypad Start/Stop and Speed

REMote Terminal strip operation using Increase/Decrease

NOTES:

1.

Electronic Motor Operated Potentiometer (EMOP): simulates the INC/DEC keys on
keypad using external remote N/O pushbuttons

2.

Commanded output frequency returns to the value of parameter 301 (Min Frequen-
cy) when the drive is stopped.

3.

Commanded output frequency remains at the previous setpoint when the drive is
stopped.

4.

The parameters that set the functions of the designated digital inputs for EMOP

must be configured as “EMOP+” and “EMOP–” to complete the implementation.

109 Power On Hours

Read-Only

Range: 0–65535 h
Level 2

110 Stator Freq

Read-Only

Range: 0.0–400.0 Hz
Level 2

111 DC Bus Voltage

Read-Only

Range: 0–1000 Vdc
Levels 1, 2

115 Drive Power Out

Read-Only

Range: 0.0–200.0%
Level 2

201 Input Mode

Default = Local only

Range: Text string
Levels 1, 2

«
...
61
62
63
64
65
...
»

Содержание 50X





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 50X

Бренд: Walchem Страницы: 10

Бренд: Tapeswitch Страницы: 13

Бренд: Ickle Bubba Страницы: 23

Бренд: ZEHUS Страницы: 28

Бренд: Valfonta Страницы: 12

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Campbell Страницы: 8

Бренд: Campbell Страницы: 22

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Samson Страницы: 52

Бренд: J3C Страницы: 2

Бренд: IDTECK Страницы: 94

Бренд: jbc Страницы: 44

Бренд: jbc Страницы: 8

Бренд: janitza Страницы: 58

Бренд: Lattice Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды