background image

using macro mode and getting a quick start

 vacon 

 

50

                                  24-hour s358 (0)40 837 1150 • Email: [email protected]

 6

490 Appl Macro

Default: Factory

Range: Text string
Macro

This parameter configures what macro will be active in the drive. A macro will change 
a default or visibility of a parameter.

The following data values may be assigned to this parameter:

Macro

Description

Factory

Provides a simple way to restore factory default parame-
ter listings.

Fan

Provides a basic set-up for Fan applications, including V/
Hz curve and terminal strip operation in Level 1 program-
ming.

Fan w/PI

Provides a simple set-up for Fan applications that require 
process control. Parameters such as V/Hz curve, terminal 
strip operation, and PI configuration are available in Level 
1 programming.

Pump

Provides a basic set-up for Pump applications, including 
V/Hz curve and terminal strip operation in Level 1 pro-
gramming.

Pump w/PI

Provides a simple set-up for Pump applications requiring 
process control. Parameters such as V/Hz curve, terminal 
strip operation, and PI configuration are available in Level 
1 programming.

Vector

Activates the sensorless vector control algorithm. When            

an operation requires low speed and high torque,      this 
macro should be activated. Note that in Vector control,the 
drive automatically runs the the Motor Rs measurements 
when leaving PROGram mode.

491 Seq Appl

Default: Disabled

Range: Text string
Macro

This parameter configures sequencer parameters are visible and the time base of the 
sequencer. The time base may change depending on the timing loops used.

The following data values may be assigned to this parameter:

Macro Value

Description

Disabled

Sequencer disabled and parameters hidden.

1sec Base

Sequencer enabled and 1 second time base.

.1sec Base

Sequencer enabled and 0.1 second time base.

.01sec Base

Sequencer enabled and 0.01 second time base.

492 SIO Visible

Default: No

Range: Text string
Macro

This parameter configures whether SIO parameters are visible.

The following data values may be assigned to this parameter:

Macro Value

Description

No

SIO parameters hidden

Yes

SIO parameters visible

Содержание 50X





































































































































Отзывы: