Vacon 50X Скачать руководство пользователя

Страница: 105 / 132

troubleshooting

vacon

104

24-hour s358 (0)40 837 1150 • Email: [email protected]

Pwr Wir-

ing

Power wiring er-

ror

This fault flags a problem

with the drive wiring.

Check that input power wiring is

not connected to load power termi-

nals. Consult VACON.

This fault can occur if an

IOC fault is detected during

the power wiring test.

Low Volt-

age

Low voltage trip

This fault occurs if a power

dip occurs when the drive

is operating, and the drive

is not able to ride through

the power dip before shut-

ting off outputs.

Verify that input line power is within

the drive’s specifications. Add a

transformer or reduce demands to

power feed. Consult VACON.

1Ph Over-

load

1Ph overload

If the user configures pa-

rameter 517 (Single Phase)

for singlephase operation,

this fault occurs if the bus

voltage ripple is outside

the limit of the drive.

Check that input power demand

does not exceed the drive’s capaci-

ty for single-phase operation. Con-

sult VACON.

RS Meas.

Fail

Stator resistance

measurement

failed

If the drive cannot measure

the stator resistance prop-

erly, this fault occurs.

Try the routine again and if the fault

occurs twice, consult VACON.

Fan Loss

Loss of fan con-

trol or operation

There is a problem with the

heat sink fan.

Consult VACON.

There is a problem with the

internal fan. This occurs

only on Size 4 and 5 mod-

els. All other models dis-

play a fan error warning.

Note that this is lack of fan

control, so the fan can be

spinning and this fault will

still occur. This can happen

if the fan is on and should

not be, or if the fan feed-

back signals are obstruct-

ed from getting to the

control board.

Code

Fault
Display

Description

Adv.

Fault
Code

Explanation

Suggestions for Recovery

Note: Shaded faults are auto-resettable, except where noted.

Table 31:Vacon 50X Fault Codes

Содержание 50X





































































































































Результаты поиска

Содержание 50X

Отзывы:

Похожие инструкции для 50X

Бренды по названию

Популярные бренды

Vacon 50X, Руководство пользователя

Результаты поиска

Содержание 50X

Отзывы:

Похожие инструкции для 50X

Бренды по названию

Популярные бренды