Vacon 50X Скачать руководство пользователя | Manualshive

Страница: 46 / 132

background image

45

vacon

keypad operation and programming

Tel. +358 (0)201 2121 • Fax +358 (0)201 212205

5

5.5 Programming

5.5.1 Accessing Parameters

When PROG (or SHIFT+PROG) is pressed after application of power or a fault reset, parameter 201, Input
Mode, is always the first parameter displayed. Figure 21 shows a typical programming display.

Figure 21: Typical Programming Display

If a different parameter is accessed and Program mode is exited, that parameter is the first one displayed
the next time Program mode is entered. The drive remembers a different “last parameter accessed” for
Levels 1 and 2.

5.5.2 Changing the Display Scroll Rate

Pressing the INC or DEC keys (up or down arrows) arrows causes the display to scroll at a slow rate. To
increase the scroll rate, hold the SHIFT key at the same time that you press the INC key. Release the
SHIFT key to return to the slow scroll rate. This procedure works in all programming and operation
modes.

5.5.3 Programming Procedure

To program the value of a parameter, follow these steps:

1.

Press the Program (PROG) key to enter Level 1 Program mode. To enter Level 2,
press SHIFT+PROG. The P indicator will appear on the display. You must enter one
level of programming or the other; you cannot switch between levels without exiting
Program mode.

Note that some parameters cannot be changed in Run mode. For example, if you
wish to program parameter 201, Input Mode, you must stop the drive before
beginning programming. Refer to the Parameter Summary Table at the front of
this manual to see which parameters cannot be changed in Run mode (they
appear as shaded entries in the table).

2.

Press the INC/DEC keys to access the desired parameter.

3.

Press the SHIFT key to allow the value to be changed. The P indicator starts to blink.

4.

Press the INC/DEC keys to select the new value.

5.

Press the ENTER key to store the new value. The display shows “Stored” for one
second.

6.

Press the PROG key to exit the Program mode, or the INC/DEC keys to select a new
parameter.

To program a text parameter, follow these steps:

1.

Like other parameters, text parameters use the INC/DEC (up/down arrow) and
SHIFT keys for editing. A line appears under the character that you are changing.

2.

Press SHIFT to advance to the next character that you want to change.

3.

Use the INC or DEC keys to change the character value.

4.

Press ENTER to store the edited text.

«
...
44
45
46
47
48
...
»

Содержание 50X





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 50X

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

ServeRAID M5014

Бренд: IBM Страницы: 106

Бренд: Campbell Страницы: 8

Бренд: Campbell Страницы: 22

Бренд: Eaton Страницы: 12

ESD-5550 Series

Бренд: GAC Страницы: 12

Бренд: MAKOT Страницы: 6

traxon e:cue LCE-mx

Бренд: Osram Страницы: 35

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: Cypress Страницы: 2

Бренд: Dudley Страницы: 8

PLATINUM PS-9003

Бренд: HydroQuip Страницы: 24

Бренд: H3C Страницы: 11

Бренд: Nanjing Putian Datang Information Electronics Co., Ltd. Страницы: 2

Бренд: DUNIWAY Stockroom Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды