Vacon 50X Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 132

background image

19

vacon

receiving and installation

Tel. +358 (0)201 2121 • Fax +358 (0)201 212205

3

3. Receiving and Installation

3.1 Preliminary Inspection

Before storing or installing the Vacon 50X AC drive, thoroughly inspect the device for possible shipping
damage. Upon receipt:

1. Remove the drive from its package and inspect exterior for shipping damage. If damage is apparent, no-

tify the shipping agent and your sales representative.

2. Remove the cover and inspect the drive for any apparent damage or foreign objects. (See Figure 7 on

page 21 for locations of cover screws.) Ensure that all mounting hardware and terminal connection

hardware is properly seated, securely fastened, and undamaged.

3. Read the technical data label affixed to the drive and ensure that the correct horsepower and input volt-

age for the application has been purchased.

4. If you will be storing the drive after receipt, place it in its original packaging and store it in a clean, dry

place free from direct sunlight or corrosive fumes, where the ambient temperature is not less than –20

°C (–4 °F) or greater than +65 °C (+149 °F).

3.2 Installation Precautions

Improper installation of the Vacon 50X AC drive will greatly reduce its life. Be sure to observe the follow-
ing precautions when selecting a mounting location. Failure to observe these precautions may void the
warranty!

•

Do not install the drive in a place subjected to high temperature, high humidity,
excessive vibration, corrosive gases or liquids, or airborne dust or metallic
particles. See Chapter 2 for temperature, humidity, and maximum vibration limits.

•

Do not mount the drive near heat-radiating elements or in direct sunlight.

•

Mount the drive vertically and do not restrict the air flow to the heat sink fins.

•

The drive generates heat. Allow sufficient space around the unit for heat dissipation.
See “Dissipation Requirements” on page 20.

CAUTION

EQUIPMENT DAMAGE HAZARD
Do not operate or install any drive that appears damaged.
Failure to follow this instruction can result in injury or equipment damage.

«
...
18
19
20
21
22
...
»

Содержание 50X





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 50X

Бренд: Eaton Страницы: 50

Бренд: Lattice Semiconductor Страницы: 30

Бренд: WAFER Страницы: 15

Бренд: KELCO Страницы: 36

Бренд: Badger Basket Страницы: 3

Бренд: BADLANDS Страницы: 2

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 157

Бренд: Vanderbilt Страницы: 2

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

Бренд: Parker Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды