Vacon 50X Скачать руководство пользователя

Страница: 103 / 132

troubleshooting

vacon

102

24-hour s358 (0)40 837 1150 • Email: [email protected]

Vac Im-

blnce

Input voltage im-

balance

The drive has detected a

singlephase condition or a

voltage imbalance outside

the drive’s rating while

running a load that could

be damaging to the drive.

Check input voltage and current for

imbalance, and correct.

OverVolt-

age

Overvoltage con-

dition

The drive has detected an

overvoltage condition dur-

ing power-up (not auto-re-

settable).

Verify incoming line power is within

specification. Add reactor or trans-

former to correct.

1, 3

The drive has detected an

overvoltage condition dur-

ing a running condition.

Verify incoming line power and

check for regenerative load. Re-

duce Regen load or add dynamic

braking resistors. Regen Current

Limit may help; consult VACON.

The drive has detected an

overvoltage condition on

power-up on the load side.

Verify incoming line power is within

specification. Add reactor or trans-

former to correct.

Dyn Brake

Dynamic brake

overload

The DB circuit is active on

power-up (not auto-reset-

table)

Check for failed braking transistor.

Consult VACON.

The DB circuit is being ac-

tivated for too long, possi-

bly causing the resistor to

overheat or fail.

Reduce braking cycle or increase

capacity. Activate current limit;

consult VACON.

The DB circuit is overload-

ed because of too large a

regenerative load.

Reduce braking cycle or increase

capacity. Activate current limit;

consult VACON.

3, 4, 5

The DB circuit is faulty on

power-up (not auto-reset-

table).

OverCur-

rent

Overcurrent con-

dition

The drive sensed an over-

current condition on pow-

erup (not auto-resettable).

Check for failed output power de-

vice or shorted motor.

The drive sensed an over-

current condition during

operation. The current has

exceeded the safe opera-

tion point of power devices.

Reduce load on motor. Verify that

Motor FLA is programmed correct-

ly. Check for mechanical binding

and shock loading.

Over

Temp

Over-tempera-

ture condition

The temperature of the

heatsink exceeded a tem-

perature limit.

Check that ambient temperature

does not exceed drive’s rating.

Check for fan operation (assuming

drive has fans installed).

The temperature of the

control board exceeded a

temperature limit.

Check that ambient temperature

does not exceed drive’s rating.

Check for fan operation (assuming

drive has fans installed).

The drive sensed the heat-

sink thermistor sensor is

faulty or not connected

properly.

Check thermistor connections or

replace. Consult VACON.

The drive sensed the con-

trol board thermistor sen-

sor is faulty or not

connected properly.

Check thermistor connections or

replace. Consult VACON.

Motor TOL

Motor timed

overload trip

The drive detected an over-

load that exceeds the cus-

tomer’s defined overload

setting.

Check load current demand. Verify

Motor FLA is programmed to the

correct value. Verify TOL charac-

teristic is correct for the applica-

tion.

Low Temp Low temperature

This fault occurs if the

temperature of the heat-

sink falls below –10.0 de-

grees C.

Verify that ambient temperature is

within the drive’s specifications; in-

crease the ambient temperature if

necessary.

Code

Fault
Display

Description

Adv.

Fault
Code

Explanation

Suggestions for Recovery

Note: Shaded faults are auto-resettable, except where noted.

Table 31:Vacon 50X Fault Codes

Содержание 50X





































































































































Результаты поиска

Содержание 50X

Отзывы:

Похожие инструкции для 50X

Бренды по названию

Популярные бренды

Vacon 50X, Руководство пользователя

Результаты поиска

Содержание 50X

Отзывы:

Похожие инструкции для 50X

Бренды по названию

Популярные бренды